High Speed LED light E-Generator Dental Handpiece drill accessories
Technical date:
working air pressure:0.2~0.3Kgf/cm2
Completely match:Pana max LED light handpiece
Clamping force:≥3kg
Use:Extraction , cutting , grinding , drilling
rotation speed:300.000rpm~350.000rpm
Move Burs way:Push bottom
Concentricity:0~0.002um
spray:triple water spray
Press finale beating:0~0.008um
Noise:≤ 60dB
Insert:2hole/4hole
Applicable tool:High speed burs Φ1.59mm-Φ1.60mm
autoclave:135 degree
Warranty:Handpiece body 1year, cartridges 6month
brand:M&Y /OEM
Dental handpieces right use way:
1. The need to use a clean , dry , oil-free air compressors for medical use ;
2. The air pressure between 2.3-2.8kgf / cm2;
3. Place the adapter with quick connector at the bottom of a combination of dental handpieces , and confirm that the card lock fixed ;
4. Press the pedal , handpiece operation and examine whether the normal operation of the spray head . If everything is normal, you can start using the handpiece .
After each patient use , maintenance should be done as follows
1. First remove the diamond burs , and clean up all the teeth on dental handpieces precipitate ;
2. Use a metal needle to clean the spray holes and fumaroles ;
Note: The spray holes and diamond burs into 40 -degree angle , fumaroles and diamond burs to a 30 degree angle.
3. Place the clean lubricating oil is sprayed into the axial hole 1-2 seconds ( diamond burs is plugged holes ) ;
4. In the bottom of the handpiece were ( with / without quick connector ) two kinds of styling , make the right amount of lubricant is injected into the bottom ;
5. The handpiece with quick connector combination ( first determine the water switch is turned off )
6. Replace the diamond burs , surrounded by white silk cloth handpiece head ( make sure the needle does not touch the diamond burs and white gauze , so as not to tie ) ;
7. pedal depressed for about 20 seconds , look at whether there is in white gauze on any stain. If there are stains on the white gauze , again, add oil , starting from item 4 continued routine maintenance , know that white gauze until no stain ;
8. Finally, no more than 135 degrees Celsius temperature and high pressure sterilization.
Handpiece routine maintenance
Fault: the occurrence of undesirable phenomena water
( 1 ) inadequate water supply .
( 2 ) the amount of water is not uniform.
( 3 ) is not a mist of water .
( 4 ) no water completely .
Solution: Check the water blocked the site
( 1 ) pipeline : the turbines removed to check for the amount of water flowing from the pipeline . If there is no water out, it may be pipes or water treatment units system problems ( bad or wrong operation , there is not enough water pressure ) .
( 2 ) interface : the interface conductors commissioning . Without the right amount of water flowing out , it indicates a problem at the interface ( such as clogged scale water supply systems or interface loose , resulting in insufficient pressure ) .
( 3) The body of the phone : the shaft from the turbine to remove , install interface running on . If there is no outflow amount of water, it is the problem turbines within the body ( water holes or dirt clogging turbines within the water supply system clogging ) .
( 4 ) shaft : If the above three normal outflow of water , it is the axis of the core problem (water nozzle clogging ) .
Axis core spray nozzle clogging .
Solution:
( 1 ) remove the end cap , remove the spool core .
( 2 ) the brush behind the nozzle cleaning needle is removed , insert the needle straight spout .
( 3 ) nozzle cleaning needle to be inserted into the upper section of the trench ( bur through jet slot ) at the till . Part of this special brush with dust brush clean.
( 4 ) the use of three guns and other bur blowing from the side .
(5 ) mounted on the shaft head , be sure to properly install the 0 -ring .
bur easy to fall off , bur not pull it out , the axis vibration.
Solution:
(1 ) Select the bur , bur must confirm the allowable speed range specified by the manufacturer , or else when the cutting load is greater than the chuck clamping force bur easily.
( 2 ) mini- head bur should use a short handle , easy to fall off when attached to the shank burs .
( 3 ) Do not use worn tapered bur , curved bur bur missing edge , otherwise it will affect the durability of the bearing Must be drawn .
(4 ) installation bur bur confirm indeed firmly installed , if not into the depths of shallow plug can cause dangerous bur flying .
FAQ:
Do you provide OEM services?
Yes, we will do our best to meet your needs.
When will the goods be sent?
Normally 3-5 working days upon receiving payment; for a large order, further negotiation is necessary.
What are your acceptable terms of payment?
TT/ Western Union/ Money gram/Trade assurance
Can I get a discount for a large number of orders?
Yes.we will according the items quantity offer discount
How to ship the goods?
By express like DHL, FEDEX, UPS, EMS, Aramex, China post
Do your products meet the standards and certifications of the dental industry?
Yes ,We have obtained the medical device production license, as well as the ISO13485 quality certification.
How long is the warranty?
The warranty has been specified in product details of every product.
Do you provide technical support and after-sales service?
Yes, we do.
What are the advantages of the product compared to the competition?
Our products are our own research and development, which can ensure the delivery time, after-sales of follow-up products, product updates and upgrades, and market price control.
What's your MOQ?
1Piece which allows you to test our quality first at a low cost.
What is the order process?
We will provide our product brochure for you to choose the products you need, after we receive your product order, we will provide you with a quotation according to your purchase quantity, after the quotation is confirmed, we will provide you with a formal contract according to the details of the final product quantity.
You confirm the contract, after paying the deposit, we will start to arrange the order production.
After the order is completed, we will provide some product packaging pictures and packing list to you.
After paying the balance, we will ship the goods to the shipping address you provided.
We will provide you with a tracking number after delivery. After you receive the goods, you verify that the goods are the same as the order. Confirm that the quantity of the product is correct and complete the transaction.
){kind=link}